Site Loader

2N Datasheet PDF Download – LOW-FREQUENCY/LOW-NOISE JFET, 2N data sheet. 2N from Texas Instruments High-Performance Analog. Find the PDF Datasheet, Specifications and Distributor Information. 2N datasheet, 2N circuit, 2N data sheet: NJSEMI – LOW NOISE VOLTAGE,alldatasheet, datasheet, Datasheet search site for Electronic.

Author: Bajora Kazshura
Country: Mexico
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 December 2011
Pages: 271
PDF File Size: 16.40 Mb
ePub File Size: 15.88 Mb
ISBN: 674-6-56076-515-6
Downloads: 2107
Price: Free* [*Free Regsitration Required]
Uploader: Vudotaxe

L1 trims crystal frequency. Resistor across crustal prevents oscillation at undesired modes. Starting is reliable and stability is good.

2N4361 डेटा पत्रक PDF( Datasheet डाउनलोड )

View full Circuit Diagram Comments Reading Opamp selected should have open-loop gain of 5 to 10 times required gain at resonance. Adiust resistor values to tune centerfrequency. Van Dalsen, Need an Active Filter? Can also serve as test transmitter putting out up to 20 mW. L1 is 9 tums No. Damping datasneet in range dataaheetwith critical value of 1.

For high pass, take output from first opamp; for bandpass, take output from second opamp. Value of input resistor is 10K 10, ohms when gain K is 1. Sams, Indianapolis, IN,p Use R2A to trim bandwidth to exactly 0.

Finally, trim center frequency to exactly 1. Ad justments are almost perfectly noninteracting if made in sequence given.

BKJ_PDF Datasheet Download IC-ON-LINE

Altemative opamps can be and Circuit values are for 1 MHz, but tuned circult can be adjusted to other desired frequency. Q1 can be 2N or T1M Opamp can be one section of OPFY. For equivalent high-pass filter, transpose positions of resistors and capacitors. Variable Q feature is controlled by single passive RC network. Center frequency of notch filter is about 4.


Table gives values catasheet R1 and C1 for three different values of Q. Maximum selectivity, conesponding to maximum height of pass curve or depth of reject curve and minimum width of either curve, is obtained when R9 is set for maximum gain in FET Q4. If R9 is advanced far enough with switch set to pass, circuit will oscllate and give sine-wave output at tuned dataeheet.

Low-pass output contains DC to 10 Hz, and high-pass output has frequency content above 10 Hz to upper frequency limit approaching 10 MHz for opamp used. Dynamic output impedance of both outputs is less than 1 ohm.

2N Transistors – 3 in stock to buy, photo, pdf datasheet, rfq, obsolete

Both outputs have DC continuity. DC output of high-pass terminal is equal to offset voltage of integrator. Datasheett output of low-pass terminal equals DC input plus offset voltages of both opamps. Use series-resonant crystal having pF series capacitance.

2N4360 Datasheet PDF – New Jersey Semiconductor

Adjust 1K pot for reliable start-up and symmetrical square-wave output. Diodes are 1N34A or 1N Gimmick is 1 or 2 turns of insulated wire wrapped around output lead. Oscillator uses two stages, one oporating in class A and the other operating as limiter that also serves as feedback path. Pins 5 and 1 must be connected together for proper operation. Quartz crystal should be cut for operation in series-resonant mode. With minor modifications, same circuit can be used for and kHz crystals.


By adding single-transistor stage, oscillator can be used as clock generator for TTL circuits. Some plated crystals will work better datzsheet others in this circuit; third-overtone types operating on their fundamental generally give best results.

Article covers theory of operation.

Article gives design theory and covers many other types of notch filters. When signal goes outside tracking range, circuit sweeps between low- and high-frequency limits until suitable signal reappears.

Circuit is basically voltage-controlled bandpass filter using Optical Electronics active 2m4360 with analog multipliers. Frequency range is to Hz, and FM bandwidth of error-voltage output is 20 Hz. Gain is fixed at -2Q2, where Q is reciprocal of damping d and ranges from less datashert 1 to above Q is changed by varying ratio of input and feedback resistors while keeping their product constant.

For Q of 3, feedback resistor should be 36 times value of input resistor.