Site Loader

A. ASTM F is for inch-based fasteners and ASTM FM is for metric fasteners, although the designations are identical between the two. The fastener industry should be made aware of an important recent development in the realm of. ASTM fastener standard specifications. ASTM F/. ASTM F/FM: Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric.

Author: Kazralrajas Arashishicage
Country: Belgium
Language: English (Spanish)
Genre: Medical
Published (Last): 18 September 2010
Pages: 287
PDF File Size: 15.79 Mb
ePub File Size: 13.77 Mb
ISBN: 242-8-99629-612-4
Downloads: 33191
Price: Free* [*Free Regsitration Required]
Uploader: Samumi

This phenomenon is accentuated with increasing length and decreasing diameter of the screw or bolt.

The properties of the coatings shall conform to the ASTM standards for the individual? Historical Version s – view previous versions of standard.

Threaded Tip, 3 0. To secure uniformity of results, samples shall be aged at room temperature for 24 h before being subjected to the salt spray test. That standard should be consulted for more detailed information. Last previous edition F — Work Item s – proposed revisions of this standard.

ASTM F1941

C1941m processing is normally required for bolts with a ratio greater than 10 in order to minimize the extremity-to-center thickness ratio. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The testing frequency should initially establish and subsequently verify over time, the ability of a process to produce parts that do not have the potential for hydrogen embrittlement.

  ANDREW B.ABEL BEN S.BERNANKE AND DEAN CROUSHORE MACROECONOMICS PDF

If heavier coatings are required allowance for the deposit buildup must be made during the manufacture of fasteners. Link to Active This link will always route to the current Active version of the standard.

One of these should meet your needs. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Link to Active This link will always route to the current Active version of the standard.

ASTM F – Portland Bolt

With normal methods for depositing metallic coatings from aqueous solutions, there is a risk of delayed failure due to hydrogen embrittlement for case hardened fasteners and fasteners having a hardness 40 HRC or above. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The other dimensional characteristics shall be as speci? The coating material, coating thickness, chromate finish, and trivalent chromite finish shall be selected and designated.

All information presented is for general reference and does not represent a professional opinion nor the policy of an author’s employer.

The average current density is usually low enough such that the extremity-to-center coating thickness ratio is much lower than with barrel-plating. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the aztm of regulatory limitations prior to use. Combining values from the two systems may result in non-conformance with the standard.

  HOW TO BE A MENTALIST SIMON WINTHROP PDF

Thick or thin local thickness in a location other than a signi? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such atsm, are entirely their own responsibility.

ASTM / ASME spec F for Zinc Plating Which finish to choose?

Long screws and bolts have a length-to-diameter ratio atsm than 5 but less than It also highlights the differences between barrel and rack plating and makes recommendations as to the applicability of each process. It is my understanding that the darker colors are a naturally occurring process due to the hexavalent chromium and provide greater corrosion resistance.

The test methods for determining the coating thickness are de?

Current edition approved Jan. We do not specify specific plating specs; we simply use the general name.

ASTM / ASME spec F1941 for Zinc Plating … Which finish to choose?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. It is the responsibility of the user of this standard to establish asym safety and health practices and determine the applicability of regulatory limitations prior to use.

For this reason the control mechanism speci?