Site Loader

2SCL Transistor Datasheet pdf, 2SCL Equivalent. Parameters and Characteristics. TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT process). 2SC Strobe Flash Applications. Medium Power Amplifier Applications. C Datasheet, C PDF, C Data sheet, C manual, C pdf, C, datenblatt, 2SCL_13, NPN Silicon Epitaxial Transistors.

Author: Vilabar Zolohn
Country: Venezuela
Language: English (Spanish)
Genre: Marketing
Published (Last): 19 September 2015
Pages: 476
PDF File Size: 9.61 Mb
ePub File Size: 9.59 Mb
ISBN: 185-2-37854-236-3
Downloads: 25456
Price: Free* [*Free Regsitration Required]
Uploader: Nelkree

A breadboard sketch would look like this:. By continuing to use this website, you agree to their use. The transistors were rated good enough for the old circuit so they should be good enough now too. To find out more, including how to control cookies, see here: The car has no wheel that can turn so the only way of making corners is transitor having different speed on the wheels for each side.

C Datasheet catalog

So no fun, unless… And so I decided to revive this toy, not because I like RC cars that much, just because off having something to do during the day-hours of the festival and transstor recover from parties the day before. While Q6 and Q8 handle the current for their motor only, the current comes together at returns leads from each motor and is than flowing into Q10 which should so be able to handle both currents together.

From my first drawing things looked way too complicated, but after reading up a bit about DC motor control through H-bridge NPN and PNP transistor tgansistor I noticed they did exactly the same thing in this circuit. You are commenting using your Twitter account.


DC motor control (reverse engineering that old toy pt.1)

For each pin I first had 22k resistors connected to the transistor base but later I swapped these to 1k resistors as the transistors that I have never came to conduct. This site uses cookies.

As far as 1 goes, that is something I can handle in software Arduino. But then I stumbled upon one of my first electronic kid toys ever, a Raccoon RC car that was in really bad condition.

But the above on is also working, but you must keep in mind two things: The two horizontal resistors central in the picture are the motors M1 and Cc3279.

The car architecture is as following: So far example, if you want to drive forward one should make Q6 and Q8 conducting and also Q10 in the middle. Skip to content Home About. Fill in your details below or click an icon to log in: You are commenting using your WordPress.

A breadboard sketch transistro look like this: Unfortunately, the toy is like 30 years old and so off tranistor the toy is based upon analogic components instead of digital ones, and off course with the datasheets of some components are missing.

2SCL Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

Note that in transistpr image above the transistor has the base as the center pin. What is so different here to most schematics is that 2 motors are driven from the same circuit.


Notify me of new posts via email. From my measurements I found the motor control circuit to look something like this: For 2 I made sure to reuse the original design in some way but adapt it to my own needs.

Notify me of new comments via email. You are commenting using your Facebook account.

20PCS C3279 TO92 2SC3279 TO-92

Leave a Reply Cancel reply Enter your comment here Because of the remote control missing I had to reverse engineer the current circuit board inside the car. Email required Address never made public.

I however soldered mine because my breadboard is still in use for some other project. Also note transitor the above schematic the potentiometer on top which allows one to correct the differences in motors speed as one motor will never be exactly the same as the other one.

If the left wheels are turning slower than those on the right, the car will turn left. Though it did not hold me back to start measuring around and understanding what kind of voltage and current levels are involved in driving the motors, because when you get that there is not much more holding you back from throwing in an Arduino or Raspberry Pi for tranisstor to do the rest of the task.