Site Loader

This Service Manual contains all the basic information required for field service and maintenance for .. The color function is available only with the DRC. Product range. Canon imageFORMULA DRC. Drivers. image1. Back to top. Drivers · Software · Manuals · Apps · Firmware · FAQs & Help. Left Right. View and Download Canon DRC service manual online. DRC Scanner pdf manual download. Also for: Dr

Author: Najind Dougore
Country: Nepal
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 October 2017
Pages: 333
PDF File Size: 14.74 Mb
ePub File Size: 5.33 Mb
ISBN: 476-2-67343-387-5
Downloads: 59011
Price: Free* [*Free Regsitration Required]
Uploader: Goltira

Chapter 6 Troubleshooting When the Scanner Is Not Recognized The following describes possible causes of your computer not recognizing the scanner. Make sure that all the mounting parts are ready.

Replace the covers and check the operation again. Carefully close the upper scanner. N Connecting The Scsi Cable The power to the scanner is ON when you are cleaning the shading plates so be very careful.

Page They are replaced by the user or service technician. Pressing the Stop key exits the user mode.

Page 75 Shading solenoid Upper Activating the shading plate of the back reading side unit. Page 57 In this case, the brightness and contrast adjustments become invalid. Installation Location Installation Location More than mm More than More than mm mm mm with document mm tray extension closed with document tray extension, extension wire open More than mm For operation, maintenance and ventilation, make sure that there is enough space around the scanner, as shown in the illustration above.

Error Indication And Solutions To install your download click on the name of the downloaded file. Page 43 50 mm, the double feed may not be detected. Appendix This is one way of fostering response for ensuring prolonged quality manjal function, and for investigating the cause of trouble during troubleshooting.


Manuak frame Angle Output image data Image data after Image data set size image dr-9080d skew correction Fig. When To Replace Rollers Be careful not to pinch your fingers in the document tray. This page requires Javascript. Open the roller cover. Remove the rear cover. Chapter 2 Preparation Before Use Page 36 Front reading unit Front platen roller Back reading unit Upper reading roller Document tray Lower reading roller Ultrasonic receiving sensor Back platen roller Ultrasonic transmitting sensor Fig.

This cleaning must be performed by a service technician, not the user. Claw of the stopper Upper reading roller assembly Fig. Types Of Patch Code Patterns Check if the machine operates normally.

G The displayed dialog box differs depending on which Windows operating system Note you are using. Page 98 Lower entry guide plate cover up if the one-way pulley is installed Screw backwards when replacing the feed motor Lower entry guide plate belt.

Page 29 Note 2: Be sure to log on as an administrator if your system is Windows NT 4. Firmly close the roller cover until you hear it fr-9080c. The Start key mnual color from red to green.

Documents, Types of documents – Canon DR-9080C User Manual

The Revision Number is changed of the part is third column shows the used quantities. Target picture element density a Output Target picture element density a: Digital signal output Without error diffusion processing With error diffusion processing Fig.


Click the [Start] button, and then click [Settings]-[Control Panel]. Load a document and click OK to continue the registration adjustment. Cable Clamp Connector Fig. Turn over the platen unit, remove two screws Screw Beltand detach the solenoid assembly Mnaual Connector Clutch Fig.

Windows is a registered trademark of Microsoft Corporation in the U. Feed direction Ultrasonic transmitting Fig. Page 42 Turns document run into the registration roller so that Document this way the skew is corrected. After Replacing Parts Connect your computer to the scanner using the SCSI cable.

Page Index Index – A – Document tray extension. Chapter 3 Software About the Software The following software applications are provided on the setup disc that is packaged with the scanner.

imageFORMULA DRC Color Production Scanner

Service Modes Displays the version of the manal mode software. List Of Signals Page Left-end sensor illuminating all, and turning off all. Clean mmanual the ink with water and a mild detergent on a soft cloth that has been firmly wrung, and then thoroughly dry it with a dry cloth. Stopper Front reading unit Fig. Protective pad Connect the power cord.

Chapter 6 Troubleshooting Error code Cause The imprinter cover and endorser ED cover are open with the optional imprinter and endorser ED installed.